Relays

Sort by Default

Display 15 Products per page

Image	Name	Summary	Price	Buy	Categories	hf:tax:product_cat
	Holley Fuel Pump Relay Kit 30 Amp	Holley Fuel Pump Relay Kit 30 Amp This Holley kit is intended primarily for those applications running an electric pump. The long wire runs in these kinds of installations can sometimes result in a voltage drop at the electric pump. Installation of this kit is good insurance that the fuel pump will be receiving full voltage from the battery. Holley P/N 12-753 can be used with any electric fuel pump, as long as the current load is not above 30 amps. It will work with 12, 16 and 24 volt systems and comes equipped with 12 AWG that provide extra current carrying capacity with minimal voltage loss. A 30 amp relay is included with a relay socket wired with extra long leads specifically designed to reduce the number of splices required. Quality insulated crimp connectors are provided to make necessary splices where required. Detailed installation instructions are included. Features: Can be used with any electric fuel pump, as long as the current load is not above 30 amps Will work with 12, 16 and 24 volt electrical systems and comes equipped with 12 awg wires that provide extra current-carrying capacity with minimal voltage loss 30 amp relay is included with a relay socket wired with long leads specifically designed to reduce the number of splices required Quality insulated crimp connectors are provided to make the necessary splices, where required Detailed instructions included	Original price was: $174.00.Current price is: $155.95.	Holley Fuel Pump Relay Kit 30 Amp quantity	Relays	relays electrical
	Mr. Gasket Electric Fan Relay Kit with 185 Degree Temp Switch	Mr. Gasket wiring harness & relay kits protect your electrical system and provide reliable and consistent power for your high performance electric fan. These kits include high quality heavy gauge wiring, 30 amp relay, 30 amp circuit breaker, pre-wired relay connector, crimp terminals & hardware. Each kit comes with easy to follow instructions that are written specifically for that application. Features: 30 AMP Relay Wiring Harness is 100″ Long – 10-18 Ga. Wire 30 Amp Circuit Breaker 3/8″ NPT Temperature Sensor w/ 1/2″ NPT Reducer Bushing Crimp Terminals & Hardware Special Connector Allows Additional Relays to be Nested Together for Clean Installation Easy to Follow Instructions Simplify Wiring Your Electric Fan Temperature Switch Turns on Fan at 185 Degrees and Off at 170 Degrees	Original price was: $59.74.Current price is: $53.77.	Mr. Gasket Electric Fan Relay Kit with 185 Degree Temp Switch quantity	Relays	relays electrical
	Mr. Gasket Waterproof 30 Amp Relay Kit	Mr. Gasket waterproof relays are ideal for use on electric fuel pumps, water pumps, cooling fans, off-road lights, and any other application that is exposed to muddy or wet conditions. This relay handles 40 amps momentary and 30 amps for continuous use. The pigtail harness has 7 inch long leads with heavy duty 12 & 18 gauge wire. The connector has the wires molded in rubber and a gasket for a leak proof seal. Ideal for use on marine applications and vehicles that are power-washed out (Jeeps, 4×4 Trucks, UTV’s, and dirt track race cars). Features: Waterproof relay w/ pigtail harness & sealed connector 40/30Amp – 30 AMP continuous load & 40 AMP momentary 12V DC Works in normally open or normally closed circuits Pigtail wires are 7” long Wire Gauge: (3) 12 gauge wires on blue (30 common), yellow (87 normally open), red (87a normally closed) – (2) 18 gauge wires on black (85 ground) & white (86 +12V) Metal mounting bracket – can be mounted under-hood or just about any other location on vehicle Ideal for use in: marine, dirt track cars, and off-road trucks & Jeeps	Original price was: $24.39.Current price is: $21.95.	Mr. Gasket Waterproof 30 Amp Relay Kit quantity	Relays	relays electrical
	MSD Black Solid State High Current Relays	High-Current Solid-State Relay 35 Amp per channel up to 140 Amp continuous Clean up your wiring with an MSD Solid-State High Current Relay Block. This high current module takes the place of 4 standard relays and eliminates unsightly wiring. Four independent channels can be activated using either power or ground. Each channel is capable of handling up to 35 Amps of continuous current, providing up to 140 Amps of power. It also has the capability of Pulse Width Modulation (PWM). With a PWM input, you can control the output at a rate of 15 hertz and a duty cycle of 50-90%. Controls electric fans, water pumps, nitrous solenoids, auxiliary lighting and any other electrical accessories that would normally require a relay. LED status indicators ensure proper wiring and operation of each channel. Should a problem arise, the relay block has built-in automatic over-temp, short circuit, and overload protection, as well as a channel reset. The solid-state high current relay can easily be mounted using the supplied hardware and mounting tabs that can be rotated 90° to accommodate various mounting locations. It’s compact and clean design will make your wiring project a breeze. Features: Operates from 7-Volts to 20-Volt supply 4 Independent Channels, 35 Amps each continuous or 100 Amps for 8 seconds Combined total continuous current rating of 140 amps Channels can be run in parallel for devices requiring more than 35 Amp single-channel rating Clean, easy install with minimum wiring Over-temp, short circuit and overload protection Diagnostic LED’s and status indicators Multiple mounting options Single wire activation by switching power or ground Available in Red or Black A PWM signal can be used in the Solid-State Relay Module with a maximum frequency of 150 hertz and a duty cycle range from 50% to 90%.	Original price was: $223.00.Current price is: $199.95.	MSD Black Solid State High Current Relays quantity	Relays	relays electrical
	MSD Black Solid State Relay 4 Channel	Clean up your wiring with an MSD Solid State Relay Block. This module takes the place of 4 standard relays and eliminates unsightly wiring. 4 independent channels can be activated using either power or ground. Each channel is capable of handling 50 Amps for up to 8 seconds or 20 Amps of continuous current. With 4 channels providing up to 200 Amps of momentary or 80 Amps constant combined power, you can easily control electric fans, water pumps, nitrous solenoids, auxiliary lighting and any other electrical accessories that would normally require a relay. LED status indicators ensure proper wiring and operation of each channel. Should a problem arise, the relay block has built-in automatic over-temp, short circuit and overload protection. The 7564 can easily be mounted using the supplied hardware and mounting tabs that can be rotated 90° to accommodate various mounting locations. It’s compact and clean design will make your wiring project a breeze. Features: 4 Channels, Up to 20 Amps continuous each and 50 Amps for 8 seconds Clean, easy install with minimum wiring Over temp, short circuit and overload protection Diagnostic LED’s Multiple mounting options Activate with power or ground Channels can be run in parallel for devices requiring more than the single-channel rating	Original price was: $200.00.Current price is: $179.95.	MSD Black Solid State Relay 4 Channel quantity	Relays	relays electrical
	MSD Red Solid State High Current Relays	High-Current Solid-State Relay 35 Amp per channel up to 140 Amp continuous Clean up your wiring with an MSD Solid-State High Current Relay Block. This high current module takes the place of 4 standard relays and eliminates unsightly wiring. Four independent channels can be activated using either power or ground. Each channel is capable of handling up to 35 Amps of continuous current, providing up to 140 Amps of power. It also has the capability of Pulse Width Modulation (PWM). With a PWM input, you can control the output at a rate of 15 hertz and a duty cycle of 50-90%. Controls electric fans, water pumps, nitrous solenoids, auxiliary lighting and any other electrical accessories that would normally require a relay. LED status indicators ensure proper wiring and operation of each channel. Should a problem arise, the relay block has built-in automatic over-temp, short circuit, and overload protection, as well as a channel reset. The solid-state high current relay can easily be mounted using the supplied hardware and mounting tabs that can be rotated 90° to accommodate various mounting locations. It’s compact and clean design will make your wiring project a breeze. Features: Operates from 7-Volts to 20-Volt supply 4 Independent Channels, 35 Amps each continuous or 100 Amps for 8 seconds Combined total continuous current rating of 140 amps Channels can be run in parallel for devices requiring more than 35 Amp single-channel rating Clean, easy install with minimum wiring Over-temp, short circuit and overload protection Diagnostic LED’s and status indicators Multiple mounting options Single wire activation by switching power or ground Available in Red or Black A PWM signal can be used in the Solid-State Relay Module with a maximum frequency of 150 hertz and a duty cycle range from 50% to 90%.	Original price was: $223.00.Current price is: $199.95.	MSD Red Solid State High Current Relays quantity	Relays	relays electrical
	MSD Red Solid State Relay 4 Channel	Clean up your wiring with an MSD Solid State Relay Block. This module takes the place of 4 standard relays and eliminates unsightly wiring. 4 independent channels can be activated using either power or ground. Each channel is capable of handling 50 Amps for up to 8 seconds or 20 Amps of continuous current. With 4 channels providing up to 200 Amps of momentary or 80 Amps constant combined power, you can easily control electric fans, water pumps, nitrous solenoids, auxiliary lighting and any other electrical accessories that would normally require a relay. LED status indicators ensure proper wiring and operation of each channel. Should a problem arise, the relay block has built-in automatic over-temp, short circuit and overload protection. The 7564 can easily be mounted using the supplied hardware and mounting tabs that can be rotated 90° to accommodate various mounting locations. It’s compact and clean design will make your wiring project a breeze. Features: 4 Channels, Up to 20 Amps continuous each and 50 Amps for 8 seconds Clean, easy install with minimum wiring Over temp, short circuit and overload protection Diagnostic LED’s Multiple mounting options Activate with power or ground Channels can be run in parallel for devices requiring more than the single-channel rating	Original price was: $200.00.Current price is: $179.95.	MSD Red Solid State Relay 4 Channel quantity	CC/Malibu Build, Relays	cc-malibu-build relays custom-builds electrical
	Spal Electric Fan Relay Wiring Kit	SPAL electric fan relay wiring kits are designed to automatically turn on your SPAL electric fan when the air conditioning is turned on. They can also be used when dual electric fans are installed using one switching device. Features: Makes installation of your new fan a breeze Designed to safely integrate with OEM wiring Feature a waterproof 10/40 amp relay with printed wires for easy installation Harness is designed for 12V systems only Does not included thermo-switch SPAL is a trademark of SPAL Automotive S.R.L LLC Italy and used herein with the owner’s permission. SPAL is registered in the United States and may be registered in other countries	Original price was: $90.89.Current price is: $81.80.	Spal Electric Fan Relay Wiring Kit quantity	Relays	relays electrical
	Spal Electric Fan Relay Wiring Kit with 185 Degree Temp Switch	SPAL electric fan wiring harness kits are a must-have when installing electric fans. Designed to safely integrate with OEM wiring, the SPAL kits feature a waterproof relay along with printed wires which aid in installation. The wiring kits also feature stainless steel switches with optional switched override capability, fuse holder, and wiring connectors. Features: Makes installation of your new fan a breeze Designed to safely integrate with OEM wiring Feature a waterproof 10/40 amp relay with printed wires for easy installation Kit features a 3/8” NPT thermos-switch and a 3/8” to ½” NPT adapter Harness is designed for 12V systems only SPAL is a trademark of SPAL Automotive S.R.L LLC Italy and used herein with the owner’s permission. SPAL is registered in the United States and may be registered in other countries	Original price was: $157.00.Current price is: $140.95.	Spal Electric Fan Relay Wiring Kit with 185 Degree Temp Switch quantity	Relays	relays electrical